Kawasaki Ninja 250R Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 27 Results
  1. Technical
    Hi guys, I just got this as my first bike a few months ago its a 2004 and it works great for the most part but has a couple problems that caused it to not pass inspection. The main problem is that the idle is set to be around 1300-1500 RPMs but will often shoot up around 4000 RPM and take up to...
  2. Technical
    Hi, I am looking for some help/advice on my overrevving problem on my ninja 250. I have a 2011 ninja 250. About 3 week ago as I was leaving work, I put the bike into 3rd gear and it started over revving. I stopped the bike. The throttle was fully released and was not stuck but the bike...
  3. Technical
    Hi, I am looking for some help/advice on my overrevving problem on my ninja 250. I have a 2011 ninja 250. About 3 week ago as I was leaving work, I put the bike into 3rd gear and it started over revving. I stopped the bike. The throttle was fully released and was not stuck but the bike...
  4. Technical
    So bike won't start. It'll crank up and start but when I try to turn the choke up it runs for a second then dies out. Read here that I needed to drain the float bowls in the carb so i hooked up a hose to the float drain, turned the tap, and out comes the gas. It looked slightly green but what...
  5. Maintenance
    I recently installed some rear LED turn signals along with a new flasher unit on my 2012 Ninja. All the turn signals work fine like they should until about 2 weeks ago. My left two turn signals(front and rear) work perfectly but when I have my right turn signal on it works perfectly until I rev...
  6. Technical
    I recently installed some rear LED turn signals along with a new flasher unit on my 2012 Ninja. All the turn signals work fine like they should until about 2 weeks ago. My left two turn signals(front and rear) work perfectly but when I have my right turn signal on it works perfectly until I rev...
  7. Technical
    Hi, I've installed 4 LED indicators on my 2009 ninja 250r. I've replaced the flasher, installed a diode harness kit and resisters at the rear indicators. The indicators do work but there are a couple issues: 1. When riding bike and revving, indicators flash normally at normal rate, however when...
  8. New Riders
    Hey guys! I just bought an 09 250. And it seems to be having some issues. I took it to a mechanic and was told that the front forks were leaking fluid onto the front brake rotor. I was also told that some thing is wrong with the clutch, because I had just bought and had them install a new clutch...
  9. Technical
    Hello, I left my covered bike in 10-40 degree weather for two weeks only to come back to a bike that won't turn over. I'm novice at motorcycle repairs and believe it is a problem with a carb. I've removed the gas tank, I've made sure gas flows from the valve, but I don't want to waste too more...
  10. Technical
    While doing a valve adjustment I am not able to adjust one of the exhaust valves. I loosened the adjusting nut and backed off the screw and still no gap for the feeler gauge. All others adjusted fine. What does this mean? rocker arm as no free play even with screw aii of the way out. Any help?
  11. Technical
    Hey everyone! New to the forum, thanks for having me. I have just spent the last couple of days scouring the forum/google looking for a solution to this problem as well as double checking all my wiring/connections and have found nothing. Proud owner of a 2008 Ninja 250R, I have just replaced...
  12. Technical
    Hello all, Jecks here, and i am currently in need of some assistance which i am hoping to receive from here. i own a 2008 ninja 250 and have owned it for about 5 months now, for the first 2 months i had it no problems i mean its the first bike i have ridden and it was plenty powerful enough for...
  13. Technical
    Hello, I have a 2009 ninja 250 and am new to motorcycles. I bought my bike used at 2900 miles and it's at about 3100 now. I noticed the bike would die when I went to put it into first gear and I thought it just needed to warm up a but more so i gave it about 15 minutes and the RPMs are under...
  14. Technical
    --- --please delete thanks.
  15. Modifications
    Im sure anyone who has fitted aftermarket LED indicators to there 250 has come across the 4 way flash problem. I know there's a diode kit you can buy to fix it but having trouble finding one, anyone know where I can find one of these? also is there another way of fixing it? Any help is much...
  16. Technical
    I just installed in-line resistors for my front turn signals on my ninja. It will blink, then go solid, then short and turn off. It's really hit or miss. However when it does blink there is a buzzing noise near the fuse box. Is this noise normal? If not how do I get rid of it! Any help or info...
  17. Site Help and Suggestions
    Hey gang: There has been a LOT of spammers coming on the site lately, ones promoting the viewing/downloading of movies online. PLEASE use the "REPORT" button (upper left of the post's "header bar") to assist the moderators and admin in stopping these clowns. There are two major reasons...
  18. 2008+ Ninja 250
    I've got a 2008 ninja 250...i bought the bike needing some fairings to be replaced and painted so i took them off and also got rid of that big license plate bracket so i wired in led strips for rear blinkers looks great and worked great but when i plugged the dash back in now all 4 blinkers just...
  19. Technical
    My right blinker won't blink it'll just be a regular light how do I fix this? New light bulb? Sent from my iPhone using Motorcycle.com Free App
1-19 of 27 Results
Top